FormulaDen.com

Physics Chemistry Math Chemical Engineering Civil Electrical Electronics Electronics and Instrumentation Materials Science Mechanical Production Engineering Financial Health

Thickness of Plates given Total Load Carried by Plates in Compound Weld Formula

GoThickness of Plates given Load Carried by Single Fillet Lap Weld Formula

GoThickness of Plates given Load Carried by Parallel Fillet Weld Formula

Fx Copy

LaTeX Copy

The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness. Check FAQs

t plate = \frac{W}{1.414 \cdot 𝜏 \cdot L parallel + 0.707 \cdot σ t \cdot L single}

t_plate - Thickness of Plate?W - Load on weld?𝜏 - Shear Stress?L_parallel - Length of Parallel Fillet Weld?σ_t - Tensile Stress?L_single - Length of Single Fillet Lap Weld?

Thickness of Plates given Total Load Carried by Plates in Compound Weld Example

With values

With units

Only example

Here is how the Thickness of Plates given Total Load Carried by Plates in Compound Weld equation looks like with Values.

Here is how the Thickness of Plates given Total Load Carried by Plates in Compound Weld equation looks like with Units.

Here is how the Thickness of Plates given Total Load Carried by Plates in Compound Weld equation looks like.

12.6288 = \frac{9}{1.414 \cdot 2.4 \cdot 200 + 0.707 \cdot 32 \cdot 1.5}

12.6288mm = \frac{9kN}{1.414 \cdot 2.4MPa \cdot 200mm + 0.707 \cdot 32MPa \cdot 1.5mm}

12.6288 = \frac{9}{1.414 \cdot 2.4 \cdot 200 + 0.707 \cdot 32 \cdot 1.5}

Tip: Use pencil ( Pencil

) icon above to edit Input Values and Units.

Calculate

Recalculate

Solution

Copy

Reset

You are here -

Home » Category

Physics » Category

Mechanical » Category

Strength of Materials » fx Thickness of Plates given Total Load Carried by Plates in Compound Weld

Thickness of Plates given Total Load Carried by Plates in Compound Weld Solution

Follow our step by step solution on how to calculate Thickness of Plates given Total Load Carried by Plates in Compound Weld?

FIRST Step Consider the formula

t plate = \frac{W}{1.414 \cdot 𝜏 \cdot L parallel + 0.707 \cdot σ t \cdot L single}

Next Step Substitute values of Variables

∴

t plate = \frac{9kN}{1.414 \cdot 2.4MPa \cdot 200mm + 0.707 \cdot 32MPa \cdot 1.5mm}

Next Step Convert Units

∴

t plate = \frac{9000N}{1.414 \cdot 2.4E+6Pa \cdot 0.2m + 0.707 \cdot 3.2E+7Pa \cdot 0.0015m}

Next Step Prepare to Evaluate

∴

t plate = \frac{9000}{1.414 \cdot 2.4E+6 \cdot 0.2 + 0.707 \cdot 3.2E+7 \cdot 0.0015}

Next Step Evaluate

∴

t plate = 0.0126288139017983m

Next Step Convert to Output's Unit

∴

t plate = 12.6288139017983mm

LAST Step Rounding Answer

∴

t plate = 12.6288mm

Thickness of Plates given Total Load Carried by Plates in Compound Weld Formula Elements

Variables

Thickness of Plate

The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

Symbol: t_plate

Measurement: LengthUnit: mm

Note: Value should be greater than 0.

Formulas to find Thickness of Plate

Load on weld

Load on weld is the instantaneous load applied perpendicular to the specimen cross section.

Symbol: W

Measurement: ForceUnit: kN

Note: Value should be greater than 0.

Formulas to find Load on weld

Shear Stress

Shear Stress is force tending to cause deformation of a material by slippage along a plane or planes parallel to the imposed stress.

Symbol: 𝜏

Measurement: StressUnit: MPa

Note: Value should be greater than 0.

Formulas to find Shear Stress

Length of Parallel Fillet Weld

Length of Parallel Fillet Weld is the distance between two consecutive end of welds.

Symbol: L_parallel

Measurement: LengthUnit: mm

Note: Value should be greater than 0.

Formulas to find Length of Parallel Fillet Weld

Tensile Stress

Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force.

Symbol: σ_t

Measurement: PressureUnit: MPa

Note: Value should be greater than 0.

Formulas to find Tensile Stress

Length of Single Fillet Lap Weld

The Length of Single Fillet Lap Weld is the distance between two consecutive ends of welds.

Symbol: L_single

Measurement: LengthUnit: mm

Note: Value should be greater than 0.

Formulas to find Length of Single Fillet Lap Weld

Other Formulas to find Thickness of Plate

Go Thickness of Plates given Load Carried by Single Fillet Lap Weld

t plate = \frac{W}{0.707 \cdot σ t \cdot L single}

Go Thickness of Plates given Load Carried by Parallel Fillet Weld

t plate = \frac{W}{1.414 \cdot 𝜏 \cdot L parallel}

Other formulas in Analysis of Compound Weld category

Go Load Carried by Single Fillet Lap Weld

W = 0.707 \cdot σ t \cdot L single \cdot t plate

Go Allowable Tensile Stress given Load Carried by Single Fillet Lap Weld

σ t = \frac{W}{0.707 \cdot L single \cdot t plate}

Go Length of Single Fillet Lap Weld given Load Carried by Single Fillet Lap Weld

L single = \frac{W}{0.707 \cdot σ t \cdot t plate}

Go Load Carried by Parallel Fillet Weld

W = 1.414 \cdot 𝜏 \cdot L parallel \cdot t plate

How to Evaluate Thickness of Plates given Total Load Carried by Plates in Compound Weld?

Thickness of Plates given Total Load Carried by Plates in Compound Weld evaluator uses Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld+0.707*Tensile Stress*Length of Single Fillet Lap Weld) to evaluate the Thickness of Plate, Thickness of plates given total load carried by plates in compound weld is defined as the distance through the plate, as distinct from width or height. Thickness of Plate is denoted by t_plate symbol.

How to evaluate Thickness of Plates given Total Load Carried by Plates in Compound Weld using this online evaluator? To use this online evaluator for Thickness of Plates given Total Load Carried by Plates in Compound Weld, enter Load on weld (W), Shear Stress (𝜏), Length of Parallel Fillet Weld (L_parallel), Tensile Stress (σ_t) & Length of Single Fillet Lap Weld (L_single) and hit the calculate button.

FAQs on Thickness of Plates given Total Load Carried by Plates in Compound Weld

What is the formula to find Thickness of Plates given Total Load Carried by Plates in Compound Weld?

The formula of Thickness of Plates given Total Load Carried by Plates in Compound Weld is expressed as Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld+0.707*Tensile Stress*Length of Single Fillet Lap Weld). Here is an example- 12628.81 = 9000/(1.414*2400000*0.2+0.707*32000000*0.0015).

How to calculate Thickness of Plates given Total Load Carried by Plates in Compound Weld?

With Load on weld (W), Shear Stress (𝜏), Length of Parallel Fillet Weld (L_parallel), Tensile Stress (σ_t) & Length of Single Fillet Lap Weld (L_single) we can find Thickness of Plates given Total Load Carried by Plates in Compound Weld using the formula - Thickness of Plate = Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld+0.707*Tensile Stress*Length of Single Fillet Lap Weld).

What are the other ways to Calculate Thickness of Plate?

Here are the different ways to Calculate Thickness of Plate-

Thickness of Plate=Load on weld/(0.707*Tensile Stress*Length of Single Fillet Lap Weld)
Thickness of Plate=Load on weld/(1.414*Shear Stress*Length of Parallel Fillet Weld)

Can the Thickness of Plates given Total Load Carried by Plates in Compound Weld be negative?

No, the Thickness of Plates given Total Load Carried by Plates in Compound Weld, measured in Length cannot be negative.

Which unit is used to measure Thickness of Plates given Total Load Carried by Plates in Compound Weld?

Thickness of Plates given Total Load Carried by Plates in Compound Weld is usually measured using the Millimeter[mm] for Length. Meter[mm], Kilometer[mm], Decimeter[mm] are the few other units in which Thickness of Plates given Total Load Carried by Plates in Compound Weld can be measured.

Let Others Know

✖

Facebook

Twitter

Copied!

Thickness of Plates given Total Load Carried by Plates in Compound Weld Formula

​GoThickness of Plates given Load Carried by Single Fillet Lap Weld Formula

​GoThickness of Plates given Load Carried by Parallel Fillet Weld Formula

Thickness of Plates given Total Load Carried by Plates in Compound Weld Example

Thickness of Plates given Total Load Carried by Plates in Compound Weld Solution

Thickness of Plates given Total Load Carried by Plates in Compound Weld Formula Elements

Other Formulas to find Thickness of Plate

Other formulas in Analysis of Compound Weld category

How to Evaluate Thickness of Plates given Total Load Carried by Plates in Compound Weld?

FAQs on Thickness of Plates given Total Load Carried by Plates in Compound Weld

Variable Name

GoThickness of Plates given Load Carried by Single Fillet Lap Weld Formula

GoThickness of Plates given Load Carried by Parallel Fillet Weld Formula