FormulaDen.com

Physics Chemistry Math Chemical Engineering Civil Electrical Electronics Electronics and Instrumentation Materials Science Mechanical Production Engineering Financial Health

Thickness of Plates given Tensile Strength of Single Fillet Lap Joint Formula

GoThickness of Plate given Area of Double Fillet Lap Joint Weld Formula

GoThickness of Plate given Area of Parallel Fillet Weld Formula

Fx Copy

LaTeX Copy

The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness. Check FAQs

t plate = \frac{TS}{0.707 \cdot σ t \cdot l}

t_plate - Thickness of Plate?TS - Tensile Strength?σ_t - Tensile Stress?l - Length of Weld?

Thickness of Plates given Tensile Strength of Single Fillet Lap Joint Example

With values

With units

Only example

Here is how the Thickness of Plates given Tensile Strength of Single Fillet Lap Joint equation looks like with Values.

Here is how the Thickness of Plates given Tensile Strength of Single Fillet Lap Joint equation looks like with Units.

Here is how the Thickness of Plates given Tensile Strength of Single Fillet Lap Joint equation looks like.

193378.7129 = \frac{35}{0.707 \cdot 32 \cdot 8}

193378.7129mm = \frac{35MPa}{0.707 \cdot 32MPa \cdot 8mm}

193378.7129 = \frac{35}{0.707 \cdot 32 \cdot 8}

Tip: Use pencil ( Pencil

) icon above to edit Input Values and Units.

Calculate

Recalculate

Solution

Copy

Reset

You are here -

Home » Category

Physics » Category

Mechanical » Category

Strength of Materials » fx Thickness of Plates given Tensile Strength of Single Fillet Lap Joint

Thickness of Plates given Tensile Strength of Single Fillet Lap Joint Solution

Follow our step by step solution on how to calculate Thickness of Plates given Tensile Strength of Single Fillet Lap Joint?

FIRST Step Consider the formula

t plate = \frac{TS}{0.707 \cdot σ t \cdot l}

Next Step Substitute values of Variables

∴

t plate = \frac{35MPa}{0.707 \cdot 32MPa \cdot 8mm}

Next Step Convert Units

∴

t plate = \frac{3.5E+7Pa}{0.707 \cdot 3.2E+7Pa \cdot 0.008m}

Next Step Prepare to Evaluate

∴

t plate = \frac{3.5E+7}{0.707 \cdot 3.2E+7 \cdot 0.008}

Next Step Evaluate

∴

t plate = 193.378712871287m

Next Step Convert to Output's Unit

∴

t plate = 193378.712871287mm

LAST Step Rounding Answer

∴

t plate = 193378.7129mm

Thickness of Plates given Tensile Strength of Single Fillet Lap Joint Formula Elements

Variables

Thickness of Plate

The thickness of plate is the state or quality of being thick. The measure of the smallest dimension of a solid figure: a board of two-inch thickness.

Symbol: t_plate

Measurement: LengthUnit: mm

Note: Value should be greater than 0.

Formulas to find Thickness of Plate

Tensile Strength

Tensile strength is the stress at the maximum on the engineering stress-strain curve.

Symbol: TS

Measurement: PressureUnit: MPa

Note: Value can be positive or negative.

Formulas to find Tensile Strength

Tensile Stress

Tensile Stress can be defined as the magnitude of force applied along the weld, which is divided by the cross-sectional area of the weld in a direction perpendicular to the applied force.

Symbol: σ_t

Measurement: PressureUnit: MPa

Note: Value should be greater than 0.

Formulas to find Tensile Stress

Length of Weld

The Length of Weld is the linear distance of each weld segment.

Symbol: l

Measurement: LengthUnit: mm

Note: Value can be positive or negative.

Formulas to find Length of Weld

Other Formulas to find Thickness of Plate

Go Thickness of Plate given Area of Double Fillet Lap Joint Weld

t plate = \frac{A weld bed}{1.414 \cdot l}

Go Thickness of Plate given Area of Parallel Fillet Weld

t plate = \frac{A weld bed}{1.414 \cdot l}

Go Thickness of Plate given Area of Single Fillet Lap Joint Weld

t plate = \frac{A weld bed}{0.707 \cdot l}

Go Thickness of Plate given Throat Thickness for Fillet Weld

t plate = \frac{t throat}{0.707}

How to Evaluate Thickness of Plates given Tensile Strength of Single Fillet Lap Joint?

Thickness of Plates given Tensile Strength of Single Fillet Lap Joint evaluator uses Thickness of Plate = Tensile Strength/(0.707*Tensile Stress*Length of Weld) to evaluate the Thickness of Plate, Thickness of plates given tensile strength of single fillet lap joint is defined as the distance through the plate, as distinct from width or height. Thickness of Plate is denoted by t_plate symbol.

How to evaluate Thickness of Plates given Tensile Strength of Single Fillet Lap Joint using this online evaluator? To use this online evaluator for Thickness of Plates given Tensile Strength of Single Fillet Lap Joint, enter Tensile Strength (TS), Tensile Stress (σ_t) & Length of Weld (l) and hit the calculate button.

FAQs on Thickness of Plates given Tensile Strength of Single Fillet Lap Joint

What is the formula to find Thickness of Plates given Tensile Strength of Single Fillet Lap Joint?

The formula of Thickness of Plates given Tensile Strength of Single Fillet Lap Joint is expressed as Thickness of Plate = Tensile Strength/(0.707*Tensile Stress*Length of Weld). Here is an example- 1.9E+8 = 35000000/(0.707*32000000*0.008).

How to calculate Thickness of Plates given Tensile Strength of Single Fillet Lap Joint?

With Tensile Strength (TS), Tensile Stress (σ_t) & Length of Weld (l) we can find Thickness of Plates given Tensile Strength of Single Fillet Lap Joint using the formula - Thickness of Plate = Tensile Strength/(0.707*Tensile Stress*Length of Weld).

What are the other ways to Calculate Thickness of Plate?

Here are the different ways to Calculate Thickness of Plate-

Thickness of Plate=Weld Bed Area/(1.414*Length of Weld)
Thickness of Plate=Weld Bed Area/(1.414*Length of Weld)
Thickness of Plate=Weld Bed Area/(0.707*Length of Weld)

Can the Thickness of Plates given Tensile Strength of Single Fillet Lap Joint be negative?

No, the Thickness of Plates given Tensile Strength of Single Fillet Lap Joint, measured in Length cannot be negative.

Which unit is used to measure Thickness of Plates given Tensile Strength of Single Fillet Lap Joint?

Thickness of Plates given Tensile Strength of Single Fillet Lap Joint is usually measured using the Millimeter[mm] for Length. Meter[mm], Kilometer[mm], Decimeter[mm] are the few other units in which Thickness of Plates given Tensile Strength of Single Fillet Lap Joint can be measured.

Let Others Know

✖

Facebook

Twitter

Copied!