FormulaDen.com

Physics Chemistry Math Chemical Engineering Civil Electrical Electronics Electronics and Instrumentation Materials Science Mechanical Production Engineering Financial Health

Outside diameter of boss in lever Formula

Fx Copy

LaTeX Copy

outside Diameter of Lever Boss is the diameter of the outside surface of the boss of a lever. Check FAQs

D o = 2 \cdot d 1

D_o - Outside Diameter of Lever Boss?d₁ - Diameter of Lever Fulcrum Pin?

Outside diameter of boss in lever Example

With values

With units

Only example

Here is how the Outside diameter of boss in lever equation looks like with Values.

Here is how the Outside diameter of boss in lever equation looks like with Units.

Here is how the Outside diameter of boss in lever equation looks like.

23.2 = 2 \cdot 11.6

23.2mm = 2 \cdot 11.6mm

23.2 = 2 \cdot 11.6

Tip: Use pencil ( Pencil

) icon above to edit Input Values and Units.

Calculate

Recalculate

Solution

Copy

Reset

You are here -

Home » Category

Engineering » Category

Mechanical » Category

Machine Design » fx Outside diameter of boss in lever

Outside diameter of boss in lever Solution

Follow our step by step solution on how to calculate Outside diameter of boss in lever?

FIRST Step Consider the formula

D o = 2 \cdot d 1

Next Step Substitute values of Variables

∴

D o = 2 \cdot 11.6mm

Next Step Convert Units

∴

D o = 2 \cdot 0.0116m

Next Step Prepare to Evaluate

∴

D o = 2 \cdot 0.0116

Next Step Evaluate

∴

D o = 0.0232m

LAST Step Convert to Output's Unit

∴

D o = 23.2mm

Outside diameter of boss in lever Formula Elements

Variables

Outside Diameter of Lever Boss

outside Diameter of Lever Boss is the diameter of the outside surface of the boss of a lever.

Symbol: D_o

Measurement: LengthUnit: mm

Note: Value should be greater than 0.

Formulas to find Outside Diameter of Lever Boss

Diameter of Lever Fulcrum Pin

Diameter of Lever Fulcrum Pin is the diameter of the pin used at the fulcrum joint of a lever.

Symbol: d₁

Measurement: LengthUnit: mm

Note: Value should be greater than 0.

Formulas to find Diameter of Lever Fulcrum Pin

Other formulas in Lever Arm category

Go Angle between arms of lever given effort, load and net reaction at fulcrum

θ = \arccos (\frac{(W^{2}) + (P^{2}) - ({R f'}^{2})}{2 \cdot W \cdot P})

Go Depth of lever arm given width

d = 2 \cdot b l

Go Width of lever arm given depth

b l = \frac{d}{2}

Go Length of major axis for elliptical cross sectioned lever given minor axis

a = 2 \cdot b

How to Evaluate Outside diameter of boss in lever?

Outside diameter of boss in lever evaluator uses Outside Diameter of Lever Boss = 2*Diameter of Lever Fulcrum Pin to evaluate the Outside Diameter of Lever Boss, The Outside diameter of boss in lever is the outside diameter of the external surface of the boss of the fulcrum pin. Outside Diameter of Lever Boss is denoted by D_o symbol.

How to evaluate Outside diameter of boss in lever using this online evaluator? To use this online evaluator for Outside diameter of boss in lever, enter Diameter of Lever Fulcrum Pin (d₁) and hit the calculate button.

FAQs on Outside diameter of boss in lever

What is the formula to find Outside diameter of boss in lever?

The formula of Outside diameter of boss in lever is expressed as Outside Diameter of Lever Boss = 2*Diameter of Lever Fulcrum Pin. Here is an example- 23200 = 2*0.0116.

How to calculate Outside diameter of boss in lever?

With Diameter of Lever Fulcrum Pin (d₁) we can find Outside diameter of boss in lever using the formula - Outside Diameter of Lever Boss = 2*Diameter of Lever Fulcrum Pin.

Can the Outside diameter of boss in lever be negative?

No, the Outside diameter of boss in lever, measured in Length cannot be negative.

Which unit is used to measure Outside diameter of boss in lever?

Outside diameter of boss in lever is usually measured using the Millimeter[mm] for Length. Meter[mm], Kilometer[mm], Decimeter[mm] are the few other units in which Outside diameter of boss in lever can be measured.

Let Others Know

✖

Facebook

Twitter

Copied!