FormulaDen.com

Physics Chemistry Math Chemical Engineering Civil Electrical Electronics Electronics and Instrumentation Materials Science Mechanical Production Engineering Financial Health

Impedance-1 using Incident Current and Voltage (Line PL) Formula

GoImpedance-1 using Transmitted Voltage (Line PL) Formula

GoImpedance-1 using Transmitted Coefficient of Current-2 (Line PL) Formula

Fx Copy

LaTeX Copy

The Impedance of Primary Winding is the total of primary Resistance and Reactance. Check FAQs

Z 1 = \frac{V i}{I i}

Z₁ - Impedance of Primary Winding?V_i - Incident Voltage?I_i - Incident Current?

Impedance-1 using Incident Current and Voltage (Line PL) Example

With values

With units

Only example

Here is how the Impedance-1 using Incident Current and Voltage (Line PL) equation looks like with Values.

Here is how the Impedance-1 using Incident Current and Voltage (Line PL) equation looks like with Units.

Here is how the Impedance-1 using Incident Current and Voltage (Line PL) equation looks like.

0.5 = \frac{6}{12}

0.5Ω = \frac{6V}{12A}

0.5 = \frac{6}{12}

Tip: Use pencil ( Pencil

) icon above to edit Input Values and Units.

Calculate

Recalculate

Solution

Copy

Reset

You are here -

Home » Category

Engineering » Category

Electrical » Category

Power System » fx Impedance-1 using Incident Current and Voltage (Line PL)

Impedance-1 using Incident Current and Voltage (Line PL) Solution

Follow our step by step solution on how to calculate Impedance-1 using Incident Current and Voltage (Line PL)?

FIRST Step Consider the formula

Z 1 = \frac{V i}{I i}

Next Step Substitute values of Variables

∴

Z 1 = \frac{6V}{12A}

Next Step Prepare to Evaluate

∴

Z 1 = \frac{6}{12}

LAST Step Evaluate

∴

Z 1 = 0.5Ω

Impedance-1 using Incident Current and Voltage (Line PL) Formula Elements

Variables

Impedance of Primary Winding

The Impedance of Primary Winding is the total of primary Resistance and Reactance.

Symbol: Z₁

Measurement: Electric ResistanceUnit: Ω

Note: Value should be greater than 0.

Formulas to find Impedance of Primary Winding

Incident Voltage

The Incident Voltage on the transmission line is equal to half the generator voltage.

Symbol: V_i

Measurement: Electric PotentialUnit: V

Note: Value can be positive or negative.

Formulas to find Incident Voltage

Incident Current

Incident Current is the Current wave that is traveling from the sending end to the receiving end of the Transmission line during any transient condition.

Symbol: I_i

Measurement: Electric CurrentUnit: A

Note: Value can be positive or negative.

Formulas to find Incident Current

Other Formulas to find Impedance of Primary Winding

Go Impedance-1 using Transmitted Voltage (Line PL)

Z 1 = (V i - E r) \cdot \frac{Z 2 + Z 3}{V t}

Go Impedance-1 using Transmitted Coefficient of Current-2 (Line PL)

Z 1 = τ i \cdot V i \cdot \frac{Z 2}{V t}

Go Impedance-1 using Transmitted Coefficient of Current-3 (Line PL)

Z 1 = τ i \cdot \frac{Z 3}{τ v}

Go Impedance-1 for Transmitted Coefficient of Current-3 (Line PL)

Z 1 = τ i \cdot \frac{Z 3}{τ v}

Other formulas in Impedance 1,2 and 3 category

Go Impedance-2 using Transmitted Current-2 (Line PL)

Z 2 = \frac{V t}{I t}

Go Impedance-2 using Transmitted Voltage (Line PL)

Z 2 = \frac{V t}{I t}

Go Impedance-3 using Transmitted Voltage (Line PL)

Z 3 = \frac{V t}{I t}

Go Impedance-2 using Transmitted Coefficient of Voltage (Line PL)

Z 2 = (\frac{2}{Z 1 \cdot τ v}) - (\frac{1}{Z 1}) - (\frac{1}{Z 3})

How to Evaluate Impedance-1 using Incident Current and Voltage (Line PL)?

Impedance-1 using Incident Current and Voltage (Line PL) evaluator uses Impedance of Primary Winding = Incident Voltage/Incident Current to evaluate the Impedance of Primary Winding, The Impedance-1 using Incident Current and Voltage (line PL) formula is defined as a measure of the overall opposition of a circuit to current, in other words: how much the circuit impedes the flow of charge. It is like resistance, but it also takes into account the effects of capacitance and inductance. Impedance-1 is measured in ohms. Impedance of Primary Winding is denoted by Z₁ symbol.

How to evaluate Impedance-1 using Incident Current and Voltage (Line PL) using this online evaluator? To use this online evaluator for Impedance-1 using Incident Current and Voltage (Line PL), enter Incident Voltage (V_i) & Incident Current (I_i) and hit the calculate button.

FAQs on Impedance-1 using Incident Current and Voltage (Line PL)

What is the formula to find Impedance-1 using Incident Current and Voltage (Line PL)?

The formula of Impedance-1 using Incident Current and Voltage (Line PL) is expressed as Impedance of Primary Winding = Incident Voltage/Incident Current. Here is an example- 0.5 = 6/12.

How to calculate Impedance-1 using Incident Current and Voltage (Line PL)?

With Incident Voltage (V_i) & Incident Current (I_i) we can find Impedance-1 using Incident Current and Voltage (Line PL) using the formula - Impedance of Primary Winding = Incident Voltage/Incident Current.

What are the other ways to Calculate Impedance of Primary Winding?

Here are the different ways to Calculate Impedance of Primary Winding-

Impedance of Primary Winding=(Incident Voltage-Reflected Voltage)*(Impedance of Secondary Winding+Impedance of Tertiary Winding)/Transmitted Voltage
Impedance of Primary Winding=Transmission Coefficient of Current*Incident Voltage*Impedance of Secondary Winding/(Transmitted Voltage)
Impedance of Primary Winding=Transmission Coefficient of Current*Impedance of Tertiary Winding/Transmission Coefficient of Voltage

Can the Impedance-1 using Incident Current and Voltage (Line PL) be negative?

Yes, the Impedance-1 using Incident Current and Voltage (Line PL), measured in Electric Resistance can be negative.

Which unit is used to measure Impedance-1 using Incident Current and Voltage (Line PL)?

Impedance-1 using Incident Current and Voltage (Line PL) is usually measured using the Ohm[Ω] for Electric Resistance. Megohm[Ω], Microhm[Ω], Volt per Ampere[Ω] are the few other units in which Impedance-1 using Incident Current and Voltage (Line PL) can be measured.

Let Others Know

✖

Facebook

Twitter

Copied!

: Value
: Unit