FormulaDen.com

Physics Chemistry Math Chemical Engineering Civil Electrical Electronics Electronics and Instrumentation Materials Science Mechanical Production Engineering Financial Health

Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength Formula

GoForce in Slab given Number of Connectors in Bridges Formula

GoForce in Slab given Total Area of Steel Section Formula

Fx Copy

LaTeX Copy

Slab Force at maximum positive moments. Check FAQs

P on slab = A st \cdot f y

P_{on slab} - Slab Force?A_st - Area of Steel Reinforcement?f_y - Yield Strength of Steel?

Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength Example

With values

With units

Only example

Here is how the Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength equation looks like with Values.

Here is how the Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength equation looks like with Units.

Here is how the Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength equation looks like.

245 = 980 \cdot 250

245kN = 980mm² \cdot 250MPa

245 = 980 \cdot 250

Tip: Use pencil ( Pencil

) icon above to edit Input Values and Units.

Calculate

Recalculate

Solution

Copy

Reset

You are here -

Home » Category

Engineering » Category

Civil » Category

Bridge and Suspension Cable » fx Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength

Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength Solution

Follow our step by step solution on how to calculate Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength?

FIRST Step Consider the formula

P on slab = A st \cdot f y

Next Step Substitute values of Variables

∴

P on slab = 980mm² \cdot 250MPa

Next Step Convert Units

∴

P on slab = 0.001m² \cdot 2.5E+8Pa

Next Step Prepare to Evaluate

∴

P on slab = 0.001 \cdot 2.5E+8

Next Step Evaluate

∴

P on slab = 245000N

LAST Step Convert to Output's Unit

∴

P on slab = 245kN

Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength Formula Elements

Variables

Slab Force

Slab Force at maximum positive moments.

Symbol: P_{on slab}

Measurement: ForceUnit: kN

Note: Value can be positive or negative.

Formulas to find Slab Force

Area of Steel Reinforcement

The area of steel reinforcement is the area covered by the steel members in concrete in tension zone.

Symbol: A_st

Measurement: AreaUnit: mm²

Note: Value should be greater than 0.

Formulas to find Area of Steel Reinforcement

Yield Strength of Steel

Yield strength of steel is the level of stress that corresponds to the yield point.

Symbol: f_y

Measurement: StressUnit: MPa

Note: Value should be greater than 0.

Formulas to find Yield Strength of Steel

Other Formulas to find Slab Force

Go Force in Slab given Number of Connectors in Bridges

P on slab = N \cdot Φ \cdot S ultimate

Go Force in Slab given Total Area of Steel Section

P on slab = A st \cdot f y

Go Force in Slab given Effective Concrete Area

P on slab = 0.85 \cdot A concrete \cdot f c

Go Force in Slab at Maximum Positive Moments given Minimum Number of Connectors for Bridges

P on slab = N \cdot Φ \cdot S ultimate - P 3

Other formulas in Number of Connectors in Bridges category

Go Number of Connectors in Bridges

N = \frac{P on slab}{Φ \cdot S ultimate}

Go Reduction Factor given Number of Connectors in Bridges

Φ = \frac{P on slab}{N \cdot S ultimate}

Go Ultimate Shear Connector Strength given Number of Connectors in Bridges

S ultimate = \frac{P on slab}{N \cdot Φ}

Go Total Area of Steel Section given Force in Slab

A st = \frac{P on slab}{f y}

How to Evaluate Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength?

Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength evaluator uses Slab Force = Area of Steel Reinforcement*Yield Strength of Steel to evaluate the Slab Force, The Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength formula is defined as a force acting at a particular point depending on the area of steel used. Slab Force is denoted by P_{on slab} symbol.

How to evaluate Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength using this online evaluator? To use this online evaluator for Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength, enter Area of Steel Reinforcement (A_st) & Yield Strength of Steel (f_y) and hit the calculate button.

FAQs on Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength

What is the formula to find Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength?

The formula of Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength is expressed as Slab Force = Area of Steel Reinforcement*Yield Strength of Steel. Here is an example- 0.245 = 0.00098*250000000.

How to calculate Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength?

With Area of Steel Reinforcement (A_st) & Yield Strength of Steel (f_y) we can find Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength using the formula - Slab Force = Area of Steel Reinforcement*Yield Strength of Steel.

What are the other ways to Calculate Slab Force?

Here are the different ways to Calculate Slab Force-

Slab Force=No of Connector in Bridge*Reduction Factor*Ultimate Shear Connector Stress
Slab Force=Area of Steel Reinforcement*Yield Strength of Steel
Slab Force=0.85*Effective Concrete Area*28 Day Compressive Strength of Concrete

Can the Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength be negative?

Yes, the Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength, measured in Force can be negative.

Which unit is used to measure Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength?

Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength is usually measured using the Kilonewton[kN] for Force. Newton[kN], Exanewton[kN], Meganewton[kN] are the few other units in which Force in Slab at Maximum Negative Moments given Reinforcing Steel Yield Strength can be measured.

Let Others Know

✖

Facebook

Twitter

Copied!