FormulaDen.com

Physics Chemistry Math Chemical Engineering Civil Electrical Electronics Electronics and Instrumentation Materials Science Mechanical Production Engineering Financial Health

Cross sectional Area of Uncut Chip Formula

Fx Copy

LaTeX Copy

The Cross-sectional Area of Uncut Chip is the area enclosed within the outer surface of the workpiece and the line of cut followed by the single-point cutting edge. Check FAQs

A c = F \cdot D c

A_c - Cross-Sectional Area of Uncut Chip?F - Feed Rate?D_c - Depth of Cut?

Cross sectional Area of Uncut Chip Example

With values

With units

Only example

Here is how the Cross sectional Area of Uncut Chip equation looks like with Values.

Here is how the Cross sectional Area of Uncut Chip equation looks like with Units.

Here is how the Cross sectional Area of Uncut Chip equation looks like.

10.5 = 0.7 \cdot 15

10.5mm² = 0.7mm/rev \cdot 15mm

10.5 = 0.7 \cdot 15

Tip: Use pencil ( Pencil

) icon above to edit Input Values and Units.

Calculate

Recalculate

Solution

Copy

Reset

You are here -

Home » Category

Engineering » Category

Production Engineering » Category

Metal Machining » fx Cross sectional Area of Uncut Chip

Cross sectional Area of Uncut Chip Solution

Follow our step by step solution on how to calculate Cross sectional Area of Uncut Chip?

FIRST Step Consider the formula

A c = F \cdot D c

Next Step Substitute values of Variables

∴

A c = 0.7mm/rev \cdot 15mm

Next Step Convert Units

∴

A c = 0.0007m/rev \cdot 0.015m

Next Step Prepare to Evaluate

∴

A c = 0.0007 \cdot 0.015

Next Step Evaluate

∴

A c = 1.05E-05m²

LAST Step Convert to Output's Unit

∴

A c = 10.5mm²

Cross sectional Area of Uncut Chip Formula Elements

Variables

Cross-Sectional Area of Uncut Chip

The Cross-sectional Area of Uncut Chip is the area enclosed within the outer surface of the workpiece and the line of cut followed by the single-point cutting edge.

Symbol: A_c

Measurement: AreaUnit: mm²

Note: Value should be greater than 0.

Formulas to find Cross-Sectional Area of Uncut Chip

Feed Rate

Feed Rate refers to the speed at which the cutting tool advances against the workpiece. It essentially controls how much material is removed with each pass of the tool.

Symbol: F

Measurement: FeedUnit: mm/rev

Note: Value should be greater than 0.

Formulas to find Feed Rate

Depth of Cut

Depth of Cut is the tertiary cutting motion that provides a necessary depth to material that is required to remove by machining. It is usually given in the third perpendicular direction.

Symbol: D_c

Measurement: LengthUnit: mm

Note: Value should be greater than 0.

Formulas to find Depth of Cut

Other formulas in Cutting Operation category

Go Cutting Speed Angle using Resultant Cutting Speed

η = a \cos (\frac{v}{v e})

Go Mean Cutting Speed

V t = n \cdot π \cdot \frac{d w + d m}{2}

Go Average Material Removal Rate using Uncut Chip Cross-Section Area

Z t = A cs \cdot V

Go Power required for Machining Operation

P m = Z w \cdot P s

How to Evaluate Cross sectional Area of Uncut Chip?

Cross sectional Area of Uncut Chip evaluator uses Cross-Sectional Area of Uncut Chip = Feed Rate*Depth of Cut to evaluate the Cross-Sectional Area of Uncut Chip, Cross sectional Area of Uncut Chip is the area enclosed within the outer surface of the workpiece and the line of cut followed by the single-point cutting tool. It is crucial in turning because it directly affects cutting forces, surface finish, and tool life. Cross-Sectional Area of Uncut Chip is denoted by A_c symbol.

How to evaluate Cross sectional Area of Uncut Chip using this online evaluator? To use this online evaluator for Cross sectional Area of Uncut Chip, enter Feed Rate (F) & Depth of Cut (D_c) and hit the calculate button.

FAQs on Cross sectional Area of Uncut Chip

What is the formula to find Cross sectional Area of Uncut Chip?

The formula of Cross sectional Area of Uncut Chip is expressed as Cross-Sectional Area of Uncut Chip = Feed Rate*Depth of Cut. Here is an example- 1.1E+7 = 0.0007*0.015.

How to calculate Cross sectional Area of Uncut Chip?

With Feed Rate (F) & Depth of Cut (D_c) we can find Cross sectional Area of Uncut Chip using the formula - Cross-Sectional Area of Uncut Chip = Feed Rate*Depth of Cut.

Can the Cross sectional Area of Uncut Chip be negative?

No, the Cross sectional Area of Uncut Chip, measured in Area cannot be negative.

Which unit is used to measure Cross sectional Area of Uncut Chip?

Cross sectional Area of Uncut Chip is usually measured using the Square Millimeter[mm²] for Area. Square Meter[mm²], Square Kilometer[mm²], Square Centimeter[mm²] are the few other units in which Cross sectional Area of Uncut Chip can be measured.

Let Others Know

✖

Facebook

Twitter

Copied!

Cross sectional Area of Uncut Chip Formula

Cross sectional Area of Uncut Chip Example

Cross sectional Area of Uncut Chip Solution

Cross sectional Area of Uncut Chip Formula Elements

Other formulas in Cutting Operation category

How to Evaluate Cross sectional Area of Uncut Chip?

FAQs on Cross sectional Area of Uncut Chip

Variable Name