FormulaDen.com

Physics Chemistry Math Chemical Engineering Civil Electrical Electronics Electronics and Instrumentation Materials Science Mechanical Production Engineering Financial Health

Average Load Voltage Step down Chopper (Buck Converter) Formula

Fx Copy

LaTeX Copy

Load Voltage is defined as the magnitude of voltage over a complete cycle in load connected to the chopper. Check FAQs

V L = f c \cdot T on \cdot V s

V_L - Load Voltage?f_c - Chopping Frequency?T_on - Chopper On Time?V_s - Source Voltage?

Average Load Voltage Step down Chopper (Buck Converter) Example

With values

With units

Only example

Here is how the Average Load Voltage Step down Chopper (Buck Converter) equation looks like with Values.

Here is how the Average Load Voltage Step down Chopper (Buck Converter) equation looks like with Units.

Here is how the Average Load Voltage Step down Chopper (Buck Converter) equation looks like.

19.8 = 0.44 \cdot 0.45 \cdot 100

19.8V = 0.44Hz \cdot 0.45s \cdot 100V

19.8 = 0.44 \cdot 0.45 \cdot 100

Tip: Use pencil ( Pencil

) icon above to edit Input Values and Units.

Calculate

Recalculate

Solution

Copy

Reset

You are here -

Home » Category

Engineering » Category

Electrical » Category

Power Electronics » fx Average Load Voltage Step down Chopper (Buck Converter)

Average Load Voltage Step down Chopper (Buck Converter) Solution

Follow our step by step solution on how to calculate Average Load Voltage Step down Chopper (Buck Converter)?

FIRST Step Consider the formula

V L = f c \cdot T on \cdot V s

Next Step Substitute values of Variables

∴

V L = 0.44Hz \cdot 0.45s \cdot 100V

Next Step Prepare to Evaluate

∴

V L = 0.44 \cdot 0.45 \cdot 100

LAST Step Evaluate

∴

V L = 19.8V

Average Load Voltage Step down Chopper (Buck Converter) Formula Elements

Variables

Load Voltage

Load Voltage is defined as the magnitude of voltage over a complete cycle in load connected to the chopper.

Symbol: V_L

Measurement: Electric PotentialUnit: V

Note: Value can be positive or negative.

Formulas to find Load Voltage

Chopping Frequency

Chopping frequency refers to the rate at which a signal is turned on and off, or modulated, in a switching circuit. A higher chopping frequency can improve accuracy and reduce noise.

Symbol: f_c

Measurement: FrequencyUnit: Hz

Note: Value should be greater than 0.

Formulas to find Chopping Frequency

Chopper On Time

Chopper On Time refers to the time period for which chopper was in ON state.

Symbol: T_on

Measurement: TimeUnit: s

Note: Value should be greater than 0.

Formulas to find Chopper On Time

Source Voltage

Source voltage is defined as the voltage or potential difference of the source which is supplying voltage to the chopper.

Symbol: V_s

Measurement: Electric PotentialUnit: V

Note: Value should be greater than 0.

Formulas to find Source Voltage

Other formulas in Step Up or Step Down Chopper category

Go Average Load Voltage for Step down Chopper (Buck Converter)

V L(bu) = d \cdot V s

Go RMS Load Voltage for Step down Chopper (Buck Converter)

V rms(bu) = \sqrt{d} \cdot V s

Go Average Output Current for Step down Chopper (Buck Converter)

i o(bu) = d \cdot (\frac{V s}{R})

Go Average Load Voltage for Step up Chopper (Boost Converter)

V L(bo) = (\frac{1}{1 - d}) \cdot V s

How to Evaluate Average Load Voltage Step down Chopper (Buck Converter)?

Average Load Voltage Step down Chopper (Buck Converter) evaluator uses Load Voltage = Chopping Frequency*Chopper On Time*Source Voltage to evaluate the Load Voltage, The Average Load Voltage Step down Chopper (Buck Converter) formula is defined as the voltage experienced by the load connected to the buck converter circuit. Load Voltage is denoted by V_L symbol.

How to evaluate Average Load Voltage Step down Chopper (Buck Converter) using this online evaluator? To use this online evaluator for Average Load Voltage Step down Chopper (Buck Converter), enter Chopping Frequency (f_c), Chopper On Time (T_on) & Source Voltage (V_s) and hit the calculate button.

FAQs on Average Load Voltage Step down Chopper (Buck Converter)

What is the formula to find Average Load Voltage Step down Chopper (Buck Converter)?

The formula of Average Load Voltage Step down Chopper (Buck Converter) is expressed as Load Voltage = Chopping Frequency*Chopper On Time*Source Voltage. Here is an example- 19.8 = 0.44*0.45*100.

How to calculate Average Load Voltage Step down Chopper (Buck Converter)?

With Chopping Frequency (f_c), Chopper On Time (T_on) & Source Voltage (V_s) we can find Average Load Voltage Step down Chopper (Buck Converter) using the formula - Load Voltage = Chopping Frequency*Chopper On Time*Source Voltage.

Can the Average Load Voltage Step down Chopper (Buck Converter) be negative?

Yes, the Average Load Voltage Step down Chopper (Buck Converter), measured in Electric Potential can be negative.

Which unit is used to measure Average Load Voltage Step down Chopper (Buck Converter)?

Average Load Voltage Step down Chopper (Buck Converter) is usually measured using the Volt[V] for Electric Potential. Millivolt[V], Microvolt[V], Nanovolt[V] are the few other units in which Average Load Voltage Step down Chopper (Buck Converter) can be measured.

Let Others Know

✖

Facebook

Twitter

Copied!

: Value
: Unit

Average Load Voltage Step down Chopper (Buck Converter) Formula

Average Load Voltage Step down Chopper (Buck Converter) Example

Average Load Voltage Step down Chopper (Buck Converter) Solution

Average Load Voltage Step down Chopper (Buck Converter) Formula Elements

Other formulas in Step Up or Step Down Chopper category

How to Evaluate Average Load Voltage Step down Chopper (Buck Converter)?

FAQs on Average Load Voltage Step down Chopper (Buck Converter)

Variable Name